Log message:
Update argyllcms to 3.4.1
Upstream changes:
[V3.4.0 -> V3.4.1] 22nd July 2025
 - Enabled support for JETI specbos extra adapter heads.
 - Turned off erroneous strip read debugging in munki driver.
 - Fixed printtarg -T option to work again.
 - Add delay to ArgyllCMS_install_USB.exe and ArgyllCMS_uninstall_USB.exe exit \ 
so that messages can be read.
 - Changed chartread unexpected patch value warning threshold to dE 95 when no \ 
targen -c profile.

Log message:
*: recursive bump for tiff growing lerc dependency

Log message:
update argyllcms to 3.4.0
pkgsrc changes:
    -   depend on openssl to avoid it accidentially beind found but unlinkable
    -   handle new com.argyllcms.metainfo.xml file
    -   refresh line numbers in spectro/icoms_ux.c patch
upstream changelog:
[V3.3.0 -> V3.4.0] 8th July 2025
    -   Added support for Spyder and SpyderPRO (2024)
    -   Renamed proposed CIE 2012 2 and 10 degree to standard CIE 2015 2 and 10
        degree observers, as per CIE 170-2:2015.
    -   Added -Y c: option to colprof and invprofcheck to allow
        setting/overriding alibration curves for setting final ink limits.
    -   Added -Y c: option to xicclu to allow setting/overriding calibration
        curves for setting final ink limits, and added -T flag to show ink
        limits.
    -   Fixed Spyder X and X2 to not make Device Disconect noise (if such sounds
        are enabled) on MSWin.
    -   Fixed bug in colprof -nI failing for CMYK profiles.
    -   Enhanced strip reader patch recognition to reject strips that don't
        start and end on the media, as well as adding some speed compensation to
        the patch recognition for non-zerbra ruler measurements.
    -   Fixed bug in i1Pro3 strip reading where it would return bad values if
        the zerbra stripe wasn't used.
    -   Changed chartread so that it will issue warnings of possible bad row or
        patch reading even when .ti2 reference measurement is not accurate (i.e.
        no preconditioning profile used in targen.)
    -   Increased emphasis of making sure that there is contrast between patches
        at the end of rows in printtarg patch ordering for strip instruments.
    -   Added -C parameter to targen to allow overriding any calibration curves
        found in the ICC profile, used to estimage the total ink limit from that
        in the ICC profile. Also better enforces final raw computes ink limits.
    -   Modified ccxxmake so that it checks that it has actually found a white
        seeming patch to use as the L*a*b* white reference, and the patch to
        de-weight. If there is no white patch (i.e. just RGB patches) then it
        will use D65 as the L*a*b* conversion reference. ccxxmake will fail if
        there are less than 3 patches.
    -   Fixed ICC profile writing so that it clips rather than failing when
        writing a ColorantTable PCS value that is out of range. A warning to
        stderr will be issued.
    -   Changed ColorMunki driver so that it is more forgiving about unexpected
        version string lengths.
    -   Fixed dispcal and dispread so that they won't error out if there is no
        instrument but the -M parameter is provided.

Log message:
*: recursive bump for jpeg -> libjpeg-turbo switch

Log message:
argyllcms: implement timeout setting for ugen(4) on NetBSD

Log message:
Update argyllcms to 3.3.0
pkgsrc changes:
fix build on Linux
upstream changes:
[V3.2.0 -> V3.3.0] 27th September 2024
    Improved reliability of i1Pro2 startup by adding recovery delay after the \ 
getmisc instruction.
    Fixed i1pro2/3 driver to be more forgiving of wavelength calibration pushing \ 
filter offsets outside the range of raw CCD range.
    Fixed numerical bug in targen when using -V and -c with profile with zero black.
    Added support for Spyder X2 (thanks to Chris Minasians and A.K. for helping \ 
make an instrument available).
    Added support for JETI 2501 spectrometer thanks to to Omardis.
    Added -T option to targen to allow separate total ink limit for text and \ 
spacer text.
    Modified targen CMYK chart generation to apply a level of luminance boost to \ 
the resulting OFPS samples. This partially compensates for the overall darkening \ 
of the test set due to exploring the combined K response of the device. While \ 
this will reduce the sampling density and resulting profile accuracy in darker \ 
parts of the gamut, it should improve the accuracy of colors for realistic \ 
prints, which typically have a lighter average than the device CMYK gamut.
    Added extra diagnostics and -p plot detail to printcal. Added -z flag to \ 
allow setting a resulting calibration table resolution to values other than 256.
    Fix 3.2.0 bug introduced into spectro/Jamfile install that omitted spec2cie \ 
from binary distributions.
[V3.1.0 -> V3.2.0] 17th April 2024
    Added extra diagnostics to printcal.
    Added colprof -nI option, that adds inverse gamut mapping to Perceptual and \ 
Saturation A2B tables, if they are being created. This is not recommended for \ 
source profiles, since it handicaps true gamut mapping, but may be a workaround \ 
to faulty Adobe Lightroom BPC for Perceptual intent in output profiles.
    Added error message for ColorMunki spectro sensor internal cable being \ 
disconnected.
    Fixed bug in Appearance B2A conversion that appeared in V3.0 release.
    Fixed crash in chartread strip reading when given faulty .ti2 file.
    Tweaked i1d3 Rev B AIO adaptive integration time to reduce measure time to \ 
be more comparable to just using Rev A commands.
    Re-worked ARGYLL_NOT_INTERACTIVE stdin to work much better on MSWin when \ 
connected to a pipe. Removed code that empties stdin before expecting use input \ 
when ARGYLL_NOT_INTERACTIVE.
    Fixed OS X dispwin -c etc.
    Fixed colprof IGNORE_DISP_ZEROS heuristic so that it doesn't reject OLED red \ 
measurements that have a Z value of 0.0.
    Added -H option to colprof to allow setting the charTargetTag to given \ 
string, rather than automatically filling with .ti3 data.
    Changed instrument monitoring thread debug messages to only be shown on -D9, \ 
so they don't interfere with messages shown at -D8.
[V3.0.2 -> V3.1.0] 1st December 2023
    Added MSWindows USB uninstaller and libwdi based installer installer to make \ 
use on MSWindows easier.
    Added UbsDk MSWindows usb driver support code, but it is currently disabled \ 
because the release versions of UsbDk have limited usefulness as a general USB \ 
driver.
    Fixed bug in CMYK profile B2A table creation that sometimes resulted in \ 
bumpy black generation. (Only occurred when compiled using recent gcc with code \ 
optimization.)
    Changed ICC profile serialization of pure ASCII text tags to emit a warning \ 
rather than error if they are fed non-ASCII utf8 input.
    Made ICC code a little more robust against bad profiles. (Thanks to David Hoyt).
    Fixed latent bug in X11 plot code that caused window not to be created or \ 
updated when dowait == 0. This shows up on Linux as failure of spotread -S to \ 
show spectral plot.
    Fixed problem with colorhug not noticing errors from the instrument.
    Updated scanin/it8Wolf.cht to improve accuracy of grey wedge patch recognition.
    Merged some Debian patches, including spelling fixes.

Log message:
Switch BUILD_DEPENDS to TOOL_DEPENDS as had been done in pkgsrc-wip.

Log message:
Add ArgyllCMS 3.0.2
ArgyllCMS is an ICC compatible color management system, available
as Open Source. It supports accurate ICC profile creation for
scanners, cameras and film recorders, and calibration and profiling
of displays and RGB & CMYK printers. Device Link can be created
with a wide variety of advanced options, including specialized
Video calibration standards and 3dLuts.