Pine

#include "Adafruit_Si7021.h"
#include <IRLibSendBase.h>
#include <IRLib_HashRaw.h>
#include <IRLibRecvPCI.h>
#include <WebUSB.h>
#include "./data.h"

#define LED 13
// https://github.com/cyborg5/IRLib2/blob/master/IRLibProtocols/IRLibSAMD21.h#L38-L39
// For SAMD21 boards: We are recommending using Pin 5 for receiving
#define IR_RECEIVE_PIN 5

// https://github.com/cyborg5/IRLib2/blob/master/IRLibProtocols/IRLibSAMD21.h#L40-L41
// For SAMD21 boards: For sending, default pin is 9
#define IR_EMIT_PIN 9

Adafruit_Si7021 sensor = Adafruit_Si7021();
WebUSB WebUSBSerial(1, "webusb.github.io/arduino/demos/console");
IRrecvPCI myReceiver(IR_RECEIVE_PIN);
IRsendRaw mySender;
String readString;
int test = 0;
void setup() {
  SerialUSB.begin(9600);
  while (!SerialUSB) {}
  WebUSBSerial.begin(9600);
  delay(1000);
  pinMode(LED, OUTPUT);
  myReceiver.enableIRIn();
  SerialUSB.println("Starting Pine design verification test!");
  SerialUSB.println("-------------------------------------");
  SerialUSB.println("\n\nTest 1: It expects to turn ON and OFF the LED");
  blink(5);
  delay(1000);
  SerialUSB.println("\n\nTest 2: It expects to measure the humidity and temp");
  if (initSensor()) {
    SerialUSB.print("Humidity: ");
    SerialUSB.print(sensor.readHumidity(), 2);
    SerialUSB.println(" RH%");
    SerialUSB.print("Temperature: ");
    SerialUSB.print(sensor.readTemperature(), 2);
    SerialUSB.println(" C");
  }
  delay(1000);
  SerialUSB.println("\n\nTest 3: It expects to turn ON the aircon");
  SerialUSB.print("Have you pointed the circuit to the aircon? [y/n]: ");
  test = 0;
  while (test == 0) {
    while (SerialUSB.available()) {
      delay(3);
      char c = SerialUSB.read();
      readString += c;
    }
    if (readString == "y") {
      SerialUSB.println(readString);
      mySender.send(rawDataON, RAW_DATA_LEN, 38);
      SerialUSB.println("Sent Turn ON Aircon");
      readString = "";
      test = 1;
    }
  }
  delay(1000);
  SerialUSB.println("\n\nTest 4: It expects to turn OFF the aircon");
  SerialUSB.print("Have you pointed the circuit to the aircon? [y/n]: ");
  test = 0;
  while (test == 0) {
    while (SerialUSB.available()) {
      delay(3);
      char c = SerialUSB.read();
      readString += c;
    }
    if (readString == "y") {
      SerialUSB.println(readString);
      mySender.send(rawDataOFF, RAW_DATA_LEN, 38);
      SerialUSB.println("Sent Turn OFF Aircon");
      readString = "";
      test = 1;
    }
  }
  delay(1000);
  SerialUSB.println("\n\nTest 5: It expects to receive IR signals");
  SerialUSB.print("Have you pressed and pointed the remote control to Pine? [y/n]: ");
  test = 0;
  while (test == 0) {
    while (SerialUSB.available()) {
      delay(3);
      char c = SerialUSB.read();
      readString += c;
    }
    if (myReceiver.getResults()) {
      SerialUSB.print(" Received IR signal length: ");
      SerialUSB.print(recvGlobal.recvLength, DEC);
      SerialUSB.print("     ");
      myReceiver.enableIRIn();
    }
    if (readString == "y") {
      SerialUSB.println(readString);
      readString = "";
      test = 1;
    }
  }
  SerialUSB.println("\n\nTest 6: It expects to receive info from the browser");
  SerialUSB.print("Have you turned on/off led from hutscape.com/webusb-led? [y/n]: ");
  test = 0;
  while (test == 0) {
    while (SerialUSB.available()) {
      delay(3);
      char c = SerialUSB.read();
      readString += c;
    }
    if (readString == "y") {
      SerialUSB.println(readString);
      readString = "";
      test = 1;
    }
    if (WebUSBSerial && WebUSBSerial.available()) {
      int byte = WebUSBSerial.read();
      if (byte == 'H') {
        SerialUSB.print("LED ON     ");
        WebUSBSerial.write("Turning LED on.");
        digitalWrite(LED, HIGH);
      } else if (byte == 'L') {
        SerialUSB.print("LED OFF     ");
        WebUSBSerial.write("Turning LED off.");
        digitalWrite(LED, LOW);
      }
      WebUSBSerial.flush();
    }
  }
  delay(1000);
  SerialUSB.println("\n\nTest 7: It expects to send info to the browser");
  SerialUSB.print("Have you open the dev console at hutscape.com/webusb-send? [y/n]: ");
  test = 0;
  while (test == 0) {
    while (SerialUSB.available()) {
      delay(3);
      char c = SerialUSB.read();
      readString += c;
    }
    if (readString == "y") {
      SerialUSB.println(readString);
      readString = "";
      test = 1;
      WebUSBSerial.write("Hello from mcu to the browser!");
      WebUSBSerial.flush();
    }
  }
  delay(1000);
  SerialUSB.println("\n\n-------------------------------------");
  SerialUSB.println("Completed Pine design verification test!");
  SerialUSB.println("-------------------------------------");
}
void loop() { }
void blink(int num) {
  for (int i=0; i < num; i++) {
    SerialUSB.print(i+1);
    SerialUSB.print("  ");
    digitalWrite(LED, LOW);
    delay(500);
    digitalWrite(LED, HIGH);
    delay(500);
  }
}
bool initSensor() {
  if (!sensor.begin()) {
    SerialUSB.println("\nERROR: Did not find Si7021 sensor!");
    return false;
  }
  return true;
}

BOARD?=arduino:samd:arduino_zero_native
PORT := $(shell ls /dev/cu.usbmodem*)
.PHONY: default lint all flash clean
default: lint all flash clean
lint:
	cpplint --extensions=ino --filter=-legal/copyright,-whitespace/line_length *.ino
all:
	# This custom PCB does not have a crytal on pins PA00 and PA01
	# Hence, use -DCRYSTALLESS to replace the extra_flags in boards.txt
	arduino-cli compile --fqbn $(BOARD) --build-properties build.extra_flags="-DCRYSTALLESS -D__SAMD21G18A__ {build.usb_flags}" ./
flash:
	arduino-cli upload -p $(PORT) --fqbn $(BOARD)
server:
	echo "Open Chrome browser at https://localhost:8000"
	python -m SimpleHTTPServer 8000
clean:
	rm -r build